How to Flush a Tankless Water Heater (Step-by-Step Procedure) (2023)

Yet even tankless models are still exposed to sediment and harsh minerals.

Need to Hire a Plumber?

Get a free estimate online from top local home service pros in your area.

Note: This post may contain affiliate links. This means that at no cost to you, we may receive a small commission for made purchases.

(Video) Rinnai Tankless Water Heater Flush Procedure

Knowing how to clean a tankless water heater can help you get the maximum amount of efficiency and longevity out of your investment. Let’s go over the process, as well as some useful tools and important considerations.

Table of Contents

The Importance of Flushing Tankless Models

Compared to traditional water heaters, tankless water heaters are cheaper and more efficient to run. They also require far less maintenance or space to operate.

That’s why it’s important to know first why and when it’s needed, then how to flush a tankless water heater, be it gas or electric.

Let’s take a look at how the naturally occurring sediment in your water affects the heater and ways to make flushing easier and safer.

Tankless Water Heaters and Scale Buildup

Anyone who’s owned a regular water will be familiar with the need to flush the tank occasionally as a means of eliminating sediment. Tankless heaters are no exception.

Hard water contains minerals which can lead to lime scale build-up. Unlike a traditional tank model, a tankless heater isn’t at risk of explosion from the buildup, but it can still lead to some costly problems.

(Video) How To Flush A Tankless Water Heater The Easy Way | DIY Plumbing

The heat exchanger is especially sensitive to scale. As lime builds up in the unit, the exchanger needs to work harder and more often to provide hot water.

This can significantly shorten the lifespan of this component, as well as cause a marked increase in your utility bills. To make matters worse, lime buildup isn’t covered in most warranties.

How Often Should You Flush a Tankless Water Heater?

How to Flush a Tankless Water Heater (Step-by-Step Procedure) (1)

As a general rule, your tankless water heater should be flushed once per year to maintain efficiency.

However, the hardness of your water plays a part in this, and you may find it better to flush two to three times per year if your home’s water is especially poor quality. A sediment trap or softener can help with hard water to a point.

Isolation Valves

Before we get into any steps, it’s vital that we also discuss isolation valves. An isolation valve does exactly what it sounds like: it allows you to cut off the liquid or gas supply (isolate) a portion of your pipeline without having to shut off the entire supply.

The term is essentially synonymous with a shut-off valve. From your stove to toilet, a wide range of items in your house have some form of isolation valve installed for maintenance or emergency purposes.

These valves come in a variety of shapes, but they all boil down to two basic types: rotary movement (such as a ball or butterfly valve) and linear (ex: glove or diaphragm valves).

Depending upon the manufacturer and whether you had a technician do the installation, your tankless heater may or may not have an isolation valve installed.

(Video) Rinnai Flush Routine - Tankless Maintenance DIY

In the event your heater lacks this feature, we strongly urge you to get one installed and hire a professional to flush in the meantime, as it can be a major safety factor when you’re performing a flush or other maintenance.

Using Pumps and Flush Kits

How to Flush a Tankless Water Heater (Step-by-Step Procedure) (2)

One of your best friends for flushing a tankless water heater is a submersible pump. Unlike a tank heater, you don’t have large volumes of water to sweep up and pull the sediment out, so having a quality pump such as the 91250 from Superior Pump will save hours, if not days, of manual flushing.

Flushing will require a big bucket to put the pump in, as there’s no simple drainage option as there is with the average tank model, hence the need for a submersible model pump.

Another great tool is a good flush kit. These kits generally include everything you need, such as a pump, bucket, descaler, and hoses. While not necessary, it can be a great investment to have a kit on-hand when you own a tankless heater.

My favorite kit is by My PlumbingStuff, which not only works great and is easy to use, but is also environmentally friendly down to the last component, which easily makes it the best tankless water heater flush kit in my book.

How to Flush a Gas Tankless Water Heater

How to Flush a Tankless Water Heater (Step-by-Step Procedure) (3)

Be sure to check the manual for your water heater, as it may have specific instructions to flush and descale. The three top brands for gas tankless models are Rinnai, Rheem, and Noritz. For your convenience, here are specific guides for each brand:

  • Rinnai tankless water heater flush procedure
  • Rheem tankless water heater flush procedure
  • Notritz tankless water heater flush procedure

No matter which brand of gas tankless water heater you have, there are a few phases in flushing that must be done in order, but are all fairly simple to follow.

(Video) Tankless Water Heater DeScaling - How To Flush

Phase 1: Preparation

  1. Disconnect the electrical power going to the heater.
  2. Remove the access panel and use a non-contact voltage tester to make sure there’s no longer power leading to the terminal.
  3. Locate and close the gas isolation valve.
  4. Locate the hot and cold shut-off valves and close them to prevent any water getting into the unit while you work.
  5. Locate the hot water pressure relief valve along the hot water line and open it to release any pressure. Be careful, as the hot water will be hot.
  6. There will be both a cold water service port and hot water service port. Connect hoses to both of these ports.
  7. Place your submersible pump into a five-gallon bucket.
  8. Connect the cold water hose to your pump.
  9. Place the free end of the hot water hose into the bucket.
  10. Pour four gallons of undiluted virgin food-grade white vinegar into the bucket. (Note: Noritz suggests one gallon of CLR to three gallons of water as a heavy-duty alternative)

Phase 2: Flushing

  1. Open the hot and cold service ports and turn the pump on.
  2. Allow the vinegar to circulate through the heater for a minimum of one hour (longer if the pump runs at less than four gallons per minute). This breaks down the scale and flushes out the sediment.
  3. Turn the pump off and dump the vinegar.
  4. Close the cold water service port and remove the attached hose
  5. Open the cold water shut-off valve to flush out any remaining vinegar through the second hose into your bucket for about ten minutes.
  6. Close the cold water shut-off valve.
  7. Allow the water to finish draining and remove the second hose.
  8. Close the hot water service port.
  9. Remove the cold water inlet filter and (if present) hot water in-line filter.
  10. Flush the filters at a sink to remove any trapped sediment.

Phase 3: Cleanup

  1. Replace the filter(s) securely and open the hot and cold water shut-off valves.
  2. Replace the access panel.
  3. Open the gas shut-off valve.
  4. Reconnect the electrical supply.

How to Flush an Electric Tankless Water Heater

How to Flush a Tankless Water Heater (Step-by-Step Procedure) (4)

Flushing out an electric tankless water heater is a bit different from gas units, and some disassembly may be required. Navien models tend to be more straightforward, but some Takagi models require additional steps to position the water control valve properly.

  • Navien tankless water heater flush procedure
  • Takagi tankless water heater flush procedure

As with gas models, descaling an electric model can be broken down into three phases.

Phase 1: Preparation

  1. Shut off the electrical power at the breaker.
  2. Close the cold water shut-off valve.
  3. Open your faucets to allow any water to drain from the heater.
  4. Close the hot water shut-off valve.
  5. Remove the access panel and use a non-contact voltage tester to make sure there’s no longer power leading to the terminal.
  6. Remove the screws which secure the wires to the heating elements.
  7. Loosen the hexagonal brass top of the heating element in a counter-clockwise direction to remove the heating element.
  8. Inspect the heating elements for any signs of damage. A cracked element should be immediately replaced.
  9. Store the heating elements in the cooper chambers of the heater so that they can also be cleaned.

Phase 2: Flushing

  1. Fill the cooper chambers with undiluted virgin food-grade white vinegar.
  2. Allow the vinegar to sit in the chamber for 90 minutes to two hours. This will break up any scale on the elements.
  3. Drain the vinegar.
  4. Replace the heating elements and re-secure the wires.
  5. Open the cold water shut-off valve and let the tank fill.
  6. Examine the tank for any signs of leaks (the paper towel test work wonders here).
  7. Open the hot water shut-off valve.
  8. Turn on several hot water faucets and let the water run for about five minutes to flush out the vinegar and clear any air pockets from the line.

Phase 3: Cleanup

  1. Turn off all hot water taps.
  2. Close the cold water shut-off valve.
  3. Remove the cold water inlet filter and flush it under a cold tap to remove any debris.
  4. Replace the filter securely.
  5. Close the access panel and restore power at the breaker.

FAQs

How to Flush a Tankless Water Heater (Step-by-Step Procedure)? ›

How to Flush a Tankless Water Heater: Step By Step
  1. Step 1: Turn Off the Isolation Valves and Gas. ...
  2. Step 2: Connect the Hoses. ...
  3. Step 3: Attach Hoses to the Circulation Pump. ...
  4. Step 4: Add Cleaning Agent. ...
  5. Step 5: Open the Valves. ...
  6. Step 6: Flush Out the Cleaning Agent. ...
  7. Step 7: Reconnect Everything.
Jan 10, 2022

How do I flush my tankless water heater? ›

How To Flush A Tankless Water Heater The Easy Way | DIY Plumbing

How do you clean and flush a tankless hot water heater with vinegar? ›

Open the hot and cold service ports and turn the pump on. Allow the vinegar to circulate through the heater for a minimum of one hour (longer if the pump runs at less than four gallons per minute). This breaks down the scale and flushes out the sediment. Turn the pump off and dump the vinegar.

How long does it take to flush out a tankless water heater? ›

Flushing your tankless heater is a simple task, but it does take 1-2 hours to complete. For most water quality, completing this task once a year will suffice, but if you have especially hard water you may want to complete more often.

What liquid do you use to clean a tankless water heater? ›

Tankless Water Heater DeScaling - How To Flush - YouTube

How much vinegar do you need to flush a tankless water heater? ›

Use 4 gallons (15.1 liters) of undiluted white vinegar to clean your tankless water heater. Never use chemical solutions of any kind.

How often should you flush out a tankless water heater? ›

Just like a tank unit, tankless water heaters need to be flushed once per year. Homeowners with hard water should consider flushing and cleaning the unit even more frequently, perhaps every six to nine months because of the excess amounts of magnesium and calcium found in hard water supplies.

Will vinegar harm a tankless water heater? ›

Yes, vinegar will dissolve water heater sediment. Just pour the solution of water and vinegar into the tankless water heater and leave it for 24 hours. The acid contained in the vinegar will eat away the sediment buildup inside the water heater.

Can I use distilled white vinegar to flush my tankless water heater? ›

Descaling a tankless water heater is performed by circulating distilled white vinegar or a descaling cleaner through the tankless water heater for 30-min to 1-hour. A small circulation pump and a bucket is required to circulate the cleaning solution as well as flush valves that have been previously installed.

How much does it cost to flush a tankless water heater? ›

It costs around $150 to flush a tankless water heater. You especially need it at least annually if you have well water with a lot of iron. That causes more sediment buildup. The process takes about a half-hour.

What happens if you don't flush your water heater? ›

If not regularly flushed, your water heater can corrode more quickly. The sediment can also block or clog the pressure and relief valve (which helps keep your water heater from exploding).

How do I know if my water heater needs to be flushed? ›

3 Signs it is Time to Drain your Water Heater
  1. #1. Your water isn't as hot as it should be. If you are getting lukewarm water, the problem could be lime buildup around your heating elements. ...
  2. #2. You've noticed sludge in your water. ...
  3. #3. It's been more than 12 months since you last drained it.
Sep 29, 2019

What is the most common problems with tankless water heaters? ›

Here are six of the most common problems and maintenance concerns for tankless water heaters:
  • Mineral Buildup.
  • System Overload.
  • Cold Water Sandwich.
  • Air Supply or Exhaust Blockage.
  • Ignition Failure.
  • Flame Failure.
Mar 9, 2022

How much does it cost to flush a tankless water heater? ›

It costs around $150 to flush a tankless water heater. You especially need it at least annually if you have well water with a lot of iron. That causes more sediment buildup. The process takes about a half-hour.

Do electric tankless water heaters need to be flushed? ›

Both gas and electric tankless water heaters need to be flushed regularly, however it's important to note that the procedures are entirely different.

What happens if you don't clean your tankless water heater? ›

What happens if I don't flush out my tankless water heater? Mineral deposits may build up. This could cause a clog within the unit and may prevent normal heating activity. Your hot water could also fluctuate and overheat the system, impacting its efficiency.

Can I use CLR to clean my tankless water heater? ›

You can use small amounts of CLR with distilled vinegar to clean a tankless water heater. It safely removes calcium, lime, and rust deposits from several household wares, including coffee pots, showerheads, toilet bowls, and washing machine basins.

Videos

1. Rheem Tankless Water Heater Annual Maintenance Flush
(Fix It Scotty)
2. How to Flush Navien Tankless Water Heater
(Champion Plumbing)
3. How To flush a Water Heater Step by Step, Rinnai, Tankless water heater maintenance
(Koality of Life)
4. Tankless Hot Water Heater Flush Procedure - Plus Extra Tips
(Josh Of All Trades)
5. Navien Tankless Cleaning Water Heaters Now
(Water Heaters Now)
6. Tankless Water Heater Flush Step-by-step from Fox Plumbing & Heating
(David Brown)
Top Articles
Latest Posts
Article information

Author: Maia Crooks Jr

Last Updated: 03/08/2023

Views: 6539

Rating: 4.2 / 5 (63 voted)

Reviews: 94% of readers found this page helpful

Author information

Name: Maia Crooks Jr

Birthday: 1997-09-21

Address: 93119 Joseph Street, Peggyfurt, NC 11582

Phone: +2983088926881

Job: Principal Design Liaison

Hobby: Web surfing, Skiing, role-playing games, Sketching, Polo, Sewing, Genealogy

Introduction: My name is Maia Crooks Jr, I am a homely, joyous, shiny, successful, hilarious, thoughtful, joyous person who loves writing and wants to share my knowledge and understanding with you.